aloittelija kaipaa apua, Terratec cinergy c pci

DVB kortit, emolevyt, adapterit, antennit, kotelot jne
welmar
Harrastaja
Viestit: 53
Liittynyt: 06.09.2010 12:40
Paikkakunta: Helsinki

Viesti Kirjoittaja welmar » 26.09.2010 3:33

Jälleen sama ongelma kone jää jumiin ajureiden asennuksen jälkeen. Ilmeisesti ongelma liittyy näytönohjaimeen koska saan käynnistettyä vikasietoisessa graafisessa tilassa. dmesg loppu osassa on jotain outoa:
13.753093] mantis_frontend_init (0): Probing for CU1216 (DVB-C)
[ 13.756615] TDA10023: i2c-addr = 0x0c, id = 0x7d
[ 13.756617] mantis_frontend_init (0): found Philips CU1216 DVB-C frontend (TDA10023) @ 0x0c
[ 13.756645] mantis_frontend_init (0): Mantis DVB-C Philips CU1216 frontend attach success
[ 13.756862] DVB: registering adapter 0 frontend 0 (Philips TDA10023 DVB-C)...
[ 13.756960] mantis_ca_init (0): Registering EN50221 device
[ 13.757057] mantis_ca_init (0): Registered EN50221 device
[ 13.757080] mantis_hif_init (0): Adapter(0) Initializing Mantis Host Interface
[ 13.780004] IR keymap rc-vp-2040 not found
[ 13.780022] mantis_rc_init (0): rc registering failed
[ 13.780039] mantis_pci_probe (0): Mantis core init failed
[ 13.780071] Mantis 0000:05:00.0: PCI INT A disabled
[ 13.978628] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 13.978635] nvidia 0000:01:00.0: setting latency timer to 64
[ 13.978640] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[ 13.978826] NVRM: loading NVIDIA UNIX x86 Kernel Module 256.53 Fri Aug 27 21:03:42 PDT 2010
[ 14.760022] BUG: unable to handle kernel paging request at b71d0490
[ 14.760134] IP: [<f85b7e61>] mantis_hif_read_mem+0x41/0x130 [mantis]
[ 14.760216] *pdpt = 0000000000910001 *pde = 0000000000000000
[ 14.760324] Oops: 0002 [#1] SMP
[ 14.760429] last sysfs file: /sys/module/parport/initstate
[ 14.760475] Modules linked in: dm_crypt ir_sony_decoder ir_jvc_decoder ir_rc6_decoder nvidia(P) snd_hda_codec_analog snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq ir_rc5_decoder ir_nec_decoder snd_timer snd_seq_device ftdi_sio mantis lnbp21 mb86a16 usbserial ir_core stb6100 tda10021 tda10023 stb0899 stv0299 snd joydev psmouse dvb_core asus_atk0110 serio_raw lp soundcore snd_page_alloc parport dm_raid45 xor hid_microsoft usbhid hid firewire_ohci floppy pata_marvell ahci firewire_core usb_storage skge crc_itu_t libahci intel_agp sky2 agpgart

welmar
Harrastaja
Viestit: 53
Liittynyt: 06.09.2010 12:40
Paikkakunta: Helsinki

Viesti Kirjoittaja welmar » 26.09.2010 3:59

welmar kirjoitti:Jälleen sama ongelma kone jää jumiin ajureiden asennuksen jälkeen. Ilmeisesti ongelma liittyy näytönohjaimeen koska saan käynnistettyä vikasietoisessa graafisessa tilassa. dmesg loppu osassa on jotain outoa:
13.753093] mantis_frontend_init (0): Probing for CU1216 (DVB-C)
[ 13.756615] TDA10023: i2c-addr = 0x0c, id = 0x7d
[ 13.756617] mantis_frontend_init (0): found Philips CU1216 DVB-C frontend (TDA10023) @ 0x0c
[ 13.756645] mantis_frontend_init (0): Mantis DVB-C Philips CU1216 frontend attach success
[ 13.756862] DVB: registering adapter 0 frontend 0 (Philips TDA10023 DVB-C)...
[ 13.756960] mantis_ca_init (0): Registering EN50221 device
[ 13.757057] mantis_ca_init (0): Registered EN50221 device
[ 13.757080] mantis_hif_init (0): Adapter(0) Initializing Mantis Host Interface
[ 13.780004] IR keymap rc-vp-2040 not found
[ 13.780022] mantis_rc_init (0): rc registering failed
[ 13.780039] mantis_pci_probe (0): Mantis core init failed
[ 13.780071] Mantis 0000:05:00.0: PCI INT A disabled
[ 13.978628] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 13.978635] nvidia 0000:01:00.0: setting latency timer to 64
[ 13.978640] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[ 13.978826] NVRM: loading NVIDIA UNIX x86 Kernel Module 256.53 Fri Aug 27 21:03:42 PDT 2010
[ 14.760022] BUG: unable to handle kernel paging request at b71d0490
[ 14.760134] IP: [<f85b7e61>] mantis_hif_read_mem+0x41/0x130 [mantis]
[ 14.760216] *pdpt = 0000000000910001 *pde = 0000000000000000
[ 14.760324] Oops: 0002 [#1] SMP
[ 14.760429] last sysfs file: /sys/module/parport/initstate
[ 14.760475] Modules linked in: dm_crypt ir_sony_decoder ir_jvc_decoder ir_rc6_decoder nvidia(P) snd_hda_codec_analog snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq ir_rc5_decoder ir_nec_decoder snd_timer snd_seq_device ftdi_sio mantis lnbp21 mb86a16 usbserial ir_core stb6100 tda10021 tda10023 stb0899 stv0299 snd joydev psmouse dvb_core asus_atk0110 serio_raw lp soundcore snd_page_alloc parport dm_raid45 xor hid_microsoft usbhid hid firewire_ohci floppy pata_marvell ahci firewire_core usb_storage skge crc_itu_t libahci intel_agp sky2 agpgart

Lisäksi vielä ote lsmod listasta:
mantis 37330 0
lnbp21 1846 1 mantis
mb86a16 19613 1 mantis
usbserial 33100 1 ftdi_sio
ir_core 14366 6 ir_sony_decoder,ir_jvc_decoder,ir_rc6_decoder,ir_rc5_decoder,ir_nec_decoder,mantis
stb6100 6508 1 mantis
tda10021 5704 1 mantis
tda10023 5968 1 mantis
stb0899 33464 1 mantis
stv0299 8766 1 mantis
snd 49006 13 snd_hda_codec_analog,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
joydev 8735 0
psmouse 59033 0
dvb_core 86552 2 mantis,stv0299

mal--
Isäntä
Viestit: 96
Liittynyt: 13.02.2010 10:54

Viesti Kirjoittaja mal-- » 26.09.2010 12:08

welmar kirjoitti:Jälleen sama ongelma kone jää jumiin ajureiden asennuksen jälkeen. Ilmeisesti ongelma liittyy näytönohjaimeen koska saan käynnistettyä vikasietoisessa graafisessa tilassa. dmesg loppu osassa on jotain outoa:
[ 13.780004] IR keymap rc-vp-2040 not found
[ 13.780022] mantis_rc_init (0): rc registering failed
[ 13.780039] mantis_pci_probe (0): Mantis core init failed
Tuon näytönohjaimesta ehkä johtuvan ongelman lisäksi sinulla ei löydy kortin mukana tulevaa IR-vastaanotinta varten olevia näppäinkoodeja. Itse olen havainnut s2liplianin http://mercurial.intuxication.org/hg/s2-liplianin ajureilla ongelman, että näppäinkoodit sisältäviin tiedostoihin on viittattu väärin koodissa mantiksen korttien kohdalla linux/include/media/rc-map.h -tiedostossa. Siellä on näppäinkoodien kohdalla juurikin tuo rc-vp-2040 kun taas itse tiedostot on nimetty tyyliin rc-vp2040 ja siksi olen joutunut tekemään patchin tuon ongelman kiertämiseksi.

Edit: Näppäinkoodit on näköjään korjattu tuoreessa hg-versiossa, joten poistin patchin.
Viimeksi muokannut mal--, 02.10.2010 12:50. Yhteensä muokattu 1 kertaa.

welmar
Harrastaja
Viestit: 53
Liittynyt: 06.09.2010 12:40
Paikkakunta: Helsinki

Viesti Kirjoittaja welmar » 27.09.2010 0:16

Kiitos nm! Vihdoin sain kaffeinen tunnistamaan kortin kun palasin 10.10:stä 10.04 ja asensin yaVDR:n PPA:n ja asensin s2-liplianin-dkms:n. Kanavia ei kuitenkaan löydy scannaamalla fi-HTV tiedostolla kuin 3sat, RTL ja arte eikä niistäkään tule kuvaa tai ääntä. Wscan ei edelleenkään tunnista korttia joten miten saan welhon kaapeliin scannattua kanavat? Ilmeisesti pitäisi copy/pastella tämä http://dvb.swelcom.fi/vdrconf.php tallentaa johonkin en vain tiedä minne. Kokeilin usr/share/dvb/dvb-c:tä ja jotain muutakin ilman tulosta. Tai tiedosto on varmaan oikeassa paikassa mutta väärässä muodossa tai väärä tiedosto Me Tv antaa ilmoituksen: Me TV ei osaa käsitellä riviä alustavassa viritystiedostossa. Wscan, xine tai totemei tiedä kortista edlleenkään mitään mikä on mielestäni outoa.

nm
Johtava konsultti
Viestit: 3160
Liittynyt: 22.07.2005 3:00

Viesti Kirjoittaja nm » 27.09.2010 2:22

welmar kirjoitti:Ilmeisesti pitäisi copy/pastella tämä http://dvb.swelcom.fi/vdrconf.php tallentaa johonkin en vain tiedä minne. Kokeilin usr/share/dvb/dvb-c:tä ja jotain muutakin ilman tulosta. Tai tiedosto on varmaan oikeassa paikassa mutta väärässä muodossa tai väärä tiedosto
http://dvb.swelcom.fi/vdrconf.php antaa channels.confin VDR:n käyttämässä formaatissa. Useimmat muut ohjelmat käyttävät zap-formaattia. Kokeile siis tätä tiedostoa: http://dvb.swelcom.fi/channelsconf.php

welmar
Harrastaja
Viestit: 53
Liittynyt: 06.09.2010 12:40
Paikkakunta: Helsinki

Viesti Kirjoittaja welmar » 27.09.2010 11:49

Minne toi pitäisi oikein tallentaa? http://forums.gentoo.org/viewtopic-p-61 ... f53eb3aca9 sivulta löytyvän pätkän kopioin ~/.kde4/share/apps/kaffeine/scandata.dvb osoitteeseen mutta sen jäklkeen ei edes kaffeine tai me tv löytänyt korttia. Wscan ,totem ja xine ei löytänyt ennenkään, mitä voi tehdä?

nm
Johtava konsultti
Viestit: 3160
Liittynyt: 22.07.2005 3:00

Viesti Kirjoittaja nm » 27.09.2010 13:54

welmar kirjoitti:Minne toi pitäisi oikein tallentaa?
Kokeile ensin avata channels.conf suoraan vaikkapa VLC:llä: http://linux.fi/wiki/Linux_ja_digi-tv#VLC
Tällöin näet, toimiiko vastaanotto lainkaan.

Oletko muuten kokeillut tuota DVB-korttia samassa koneessa Windowsilla? Tämä auttaisi rajaamaan signaali- ja rautaongelmat pois.

welmar
Harrastaja
Viestit: 53
Liittynyt: 06.09.2010 12:40
Paikkakunta: Helsinki

Viesti Kirjoittaja welmar » 27.09.2010 15:35

Ei ole windows levyä enkä viitsi tämän takia mitään piraattia imuroida ja asennella, enneminkin yritän virittää lumileopardin toimimaan jos pitää toista järjestelmää kokeilla. .xine kansiossa ei ole mitään channels.confia mutta eikö se johdu siitä etten saa mitään scannattua? Jostain syystä enään mikään ohjelma ei tunnista korttia eli varmaan on taas uudellenasennus edessä. onneksi nyt jo tiedän mitä tehdä että mantis ajurit saa asennettua. Kyllä kai vastaanotto toimii kaffeine ainakin silloin kun vielä toimi näytti singnaaliksi 95%.

nm
Johtava konsultti
Viestit: 3160
Liittynyt: 22.07.2005 3:00

Viesti Kirjoittaja nm » 27.09.2010 15:58

welmar kirjoitti:Ei ole windows levyä enkä viitsi tämän takia mitään piraattia imuroida ja asennella, enneminkin yritän virittää lumileopardin toimimaan jos pitää toista järjestelmää kokeilla.
Cinergy C:lle ei kuitenkaan ole OS X -ajuria.
.xine kansiossa ei ole mitään channels.confia
Tiedosto pitää itse laittaa sinne, jos meinaat käyttää Xineä:

Koodi: Valitse kaikki

wget http://dvb.swelcom.fi/channelsconf.php -O .xine/channels.conf
Mutta VLC ei lue channels.confia mistään oletussijainnista vaan sille annetaan koko polku. Eli jos olet ladannut chanels.confin kotihakemistoosi ja käytät lucidin VLC:tä, komenna:

Koodi: Valitse kaikki

vlc --playlist ~/channels.conf
Jostain syystä enään mikään ohjelma ei tunnista korttia eli varmaan on taas uudellenasennus edessä.
Mitä dmesg sanoo? Mitä tiedostoja on hakemistossa /dev/dvb/adapter0 (olettaen että koneessa on vain Cinergy C eikä muita DVB-kortteja)?

welmar
Harrastaja
Viestit: 53
Liittynyt: 06.09.2010 12:40
Paikkakunta: Helsinki

Viesti Kirjoittaja welmar » 01.10.2010 21:40

Tällä hetkellä tilanne olis sellainen että kaffeine löytää kortin ja tunnistaa sen Philips TDA10021 DVB-C:nä. Myös Järjestelmä>Ylläpito>Laiteajurit näyttää Mantis ajurit ja ilmoittaa niiden olevan käytössä. Kaiken pitäisi siis olla hyvin mutta kun yritän scannata saan ilmoituksen Vastaanottolaitetta ei löydy. lspci -vnn ei myöskään näytä mitään mantiksesta tai muistakaan moduleista tai ajureista. dmesg näyttää:[ 0.254698] pci 0000:00:1c.5: PCI bridge, secondary bus 0000:02
[ 0.254700] pci 0000:00:1c.5: IO window: 0xc000-0xcfff
[ 0.254704] pci 0000:00:1c.5: MEM window: 0xfe900000-0xfe9fffff
[ 0.254707] pci 0000:00:1c.5: PREFETCH window: 0x000000f0600000-0x000000f07fffff
[ 0.254713] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:05
[ 0.254715] pci 0000:00:1e.0: IO window: 0xe000-0xefff
[ 0.254719] pci 0000:00:1e.0: MEM window: 0xfeb00000-0xfebfffff
[ 0.254723] pci 0000:00:1e.0: PREFETCH window: 0x000000f8f00000-0x000000f8ffffff
[ 0.254737] alloc irq_desc for 16 on node -1
[ 0.254739] alloc kstat_irqs on node -1
[ 0.254745] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.254748] pci 0000:00:01.0: setting latency timer to 64
[ 0.254754] pci 0000:00:1c.0: enabling device (0106 -> 0107)
[ 0.254758] alloc irq_desc for 17 on node -1
[ 0.254760] alloc kstat_irqs on node -1
[ 0.254762] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.254765] pci 0000:00:1c.0: setting latency timer to 64
[ 0.254772] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.254775] pci 0000:00:1c.4: setting latency timer to 64
[ 0.254781] pci 0000:00:1c.5: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[ 0.254784] pci 0000:00:1c.5: setting latency timer to 64
[ 0.254789] pci 0000:00:1e.0: setting latency timer to 64
[ 0.254792] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.254794] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[ 0.254796] pci_bus 0000:01: resource 0 io: [0xb000-0xbfff]
[ 0.254797] pci_bus 0000:01: resource 1 mem: [0xfa000000-0xfe8fffff]
[ 0.254799] pci_bus 0000:01: resource 2 pref mem [0xd0000000-0xdfffffff]
[ 0.254801] pci_bus 0000:04: resource 0 io: [0x1000-0x1fff]
[ 0.254803] pci_bus 0000:04: resource 1 mem: [0xf0000000-0xf03fffff]
[ 0.254804] pci_bus 0000:04: resource 2 pref mem [0xf8e00000-0xf8efffff]
[ 0.254806] pci_bus 0000:03: resource 0 io: [0xd000-0xdfff]
[ 0.254808] pci_bus 0000:03: resource 1 mem: [0xfea00000-0xfeafffff]
[ 0.254810] pci_bus 0000:03: resource 2 pref mem [0xf0400000-0xf05fffff]
[ 0.254812] pci_bus 0000:02: resource 0 io: [0xc000-0xcfff]
[ 0.254813] pci_bus 0000:02: resource 1 mem: [0xfe900000-0xfe9fffff]
[ 0.254815] pci_bus 0000:02: resource 2 pref mem [0xf0600000-0xf07fffff]
[ 0.254817] pci_bus 0000:05: resource 0 io: [0xe000-0xefff]
[ 0.254819] pci_bus 0000:05: resource 1 mem: [0xfeb00000-0xfebfffff]
[ 0.254820] pci_bus 0000:05: resource 2 pref mem [0xf8f00000-0xf8ffffff]
[ 0.254822] pci_bus 0000:05: resource 3 io: [0x00-0xffff]
[ 0.254824] pci_bus 0000:05: resource 4 mem: [0x000000-0xffffffff]
[ 0.254853] NET: Registered protocol family 2
[ 0.254929] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.255160] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.255528] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.255698] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.255700] TCP reno registered
[ 0.255751] NET: Registered protocol family 1
[ 0.255877] pci 0000:01:00.0: Boot video device
[ 0.256013] cpufreq-nforce2: No nForce2 chipset.
[ 0.256031] Scanning for low memory corruption every 60 seconds
[ 0.256096] audit: initializing netlink socket (disabled)
[ 0.256103] type=2000 audit(1285955908.255:1): initialized
[ 0.262831] highmem bounce pool size: 64 pages
[ 0.262835] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.263873] VFS: Disk quotas dquot_6.5.2
[ 0.263915] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.264297] fuse init (API version 7.13)
[ 0.264355] msgmni has been set to 1646
[ 0.264502] alg: No test for stdrng (krng)
[ 0.264540] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.264542] io scheduler noop registered
[ 0.264544] io scheduler anticipatory registered
[ 0.264545] io scheduler deadline registered
[ 0.264571] io scheduler cfq registered (default)
[ 0.264668] alloc irq_desc for 24 on node -1
[ 0.264670] alloc kstat_irqs on node -1
[ 0.264676] pcieport 0000:00:01.0: irq 24 for MSI/MSI-X
[ 0.264680] pcieport 0000:00:01.0: setting latency timer to 64
[ 0.264753] alloc irq_desc for 25 on node -1
[ 0.264754] alloc kstat_irqs on node -1
[ 0.264759] pcieport 0000:00:1c.0: irq 25 for MSI/MSI-X
[ 0.264765] pcieport 0000:00:1c.0: setting latency timer to 64
[ 0.264850] alloc irq_desc for 26 on node -1
[ 0.264851] alloc kstat_irqs on node -1
[ 0.264856] pcieport 0000:00:1c.4: irq 26 for MSI/MSI-X
[ 0.264862] pcieport 0000:00:1c.4: setting latency timer to 64
[ 0.264948] alloc irq_desc for 27 on node -1
[ 0.264949] alloc kstat_irqs on node -1
[ 0.264956] pcieport 0000:00:1c.5: irq 27 for MSI/MSI-X
[ 0.264962] pcieport 0000:00:1c.5: setting latency timer to 64
[ 0.265022] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.265097] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.265168] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.265171] ACPI: Power Button [PWRB]
[ 0.265202] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.265204] ACPI: Power Button [PWRF]
[ 0.265727] ACPI: SSDT cff7e0d0 00277 (v01 DpgPmm P001Ist 00000011 INTL 20060113)
[ 0.265953] processor LNXCPU:00: registered as cooling_device0
[ 0.266257] ACPI: SSDT cff7e350 00277 (v01 DpgPmm P002Ist 00000012 INTL 20060113)
[ 0.266469] processor LNXCPU:01: registered as cooling_device1
[ 0.269164] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.269245] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.269563] 00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.270274] brd: module loaded
[ 0.270586] loop: module loaded
[ 0.270635] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[ 0.270688] ata_piix 0000:00:1f.2: version 2.13
[ 0.270699] alloc irq_desc for 19 on node -1
[ 0.270701] alloc kstat_irqs on node -1
[ 0.270705] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.270709] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[ 0.270741] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 0.270784] scsi0 : ata_piix
[ 0.270834] scsi1 : ata_piix
[ 0.271728] ata1: SATA max UDMA/133 cmd 0x9000 ctl 0x8c00 bmdma 0x8480 irq 19
[ 0.271733] ata2: SATA max UDMA/133 cmd 0x8880 ctl 0x8800 bmdma 0x8488 irq 19
[ 0.271748] ata_piix 0000:00:1f.5: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.271751] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
[ 0.271776] ata_piix 0000:00:1f.5: setting latency timer to 64
[ 0.271800] scsi2 : ata_piix
[ 0.271833] scsi3 : ata_piix
[ 0.272701] ata3: SATA max UDMA/133 cmd 0xa000 ctl 0x9c00 bmdma 0x9480 irq 19
[ 0.272704] ata4: SATA max UDMA/133 cmd 0x9880 ctl 0x9800 bmdma 0x9488 irq 19
[ 0.272746] pata_acpi 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.272765] pata_acpi 0000:03:00.0: setting latency timer to 64
[ 0.272776] pata_acpi 0000:03:00.0: PCI INT A disabled
[ 0.272977] Fixed MDIO Bus: probed
[ 0.273000] PPP generic driver version 2.4.2
[ 0.273023] tun: Universal TUN/TAP device driver, 1.6
[ 0.273024] tun: (C) 1999-2004 Max Krasnyansky <maxk>
[ 0.273077] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.273089] alloc irq_desc for 18 on node -1
[ 0.273090] alloc kstat_irqs on node -1
[ 0.273093] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.273100] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 0.273103] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 0.273122] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[ 0.273143] ehci_hcd 0000:00:1a.7: debug port 1
[ 0.277022] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[ 0.277031] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xf9fffc00
[ 0.279952] isapnp: Scanning for PnP cards...
[ 0.291958] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[ 0.292025] usb usb1: configuration #1 chosen from 1 choice
[ 0.292044] hub 1-0:1.0: USB hub found
[ 0.292051] hub 1-0:1.0: 6 ports detected
[ 0.292095] alloc irq_desc for 23 on node -1
[ 0.292096] alloc kstat_irqs on node -1
[ 0.292100] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.292110] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 0.292112] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 0.292135] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[ 0.292153] ehci_hcd 0000:00:1d.7: debug port 1
[ 0.296031] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 0.296041] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf9fff800
[ 0.320009] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 0.320081] usb usb2: configuration #1 chosen from 1 choice
[ 0.320102] hub 2-0:1.0: USB hub found
[ 0.320107] hub 2-0:1.0: 6 ports detected
[ 0.320153] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.320166] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.320198] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.320204] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 0.320206] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 0.320230] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[ 0.320256] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000a800
[ 0.320313] usb usb3: configuration #1 chosen from 1 choice
[ 0.320329] hub 3-0:1.0: USB hub found
[ 0.320333] hub 3-0:1.0: 2 ports detected
[ 0.320367] alloc irq_desc for 21 on node -1
[ 0.320369] alloc kstat_irqs on node -1
[ 0.320373] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 0.320378] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 0.320380] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 0.320399] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[ 0.320422] uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000a880
[ 0.320482] usb usb4: configuration #1 chosen from 1 choice
[ 0.320498] hub 4-0:1.0: USB hub found
[ 0.320502] hub 4-0:1.0: 2 ports detected
[ 0.320532] uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.320536] uhci_hcd 0000:00:1a.2: setting latency timer to 64
[ 0.320538] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[ 0.320557] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
[ 0.320575] uhci_hcd 0000:00:1a.2: irq 18, io base 0x0000ac00
[ 0.320629] usb usb5: configuration #1 chosen from 1 choice
[ 0.320645] hub 5-0:1.0: USB hub found
[ 0.320649] hub 5-0:1.0: 2 ports detected
[ 0.320681] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.320685] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 0.320687] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 0.320709] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
[ 0.320727] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000a080
[ 0.320783] usb usb6: configuration #1 chosen from 1 choice
[ 0.320799] hub 6-0:1.0: USB hub found
[ 0.320803] hub 6-0:1.0: 2 ports detected
[ 0.320834] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.320838] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 0.320840] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 0.320859] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
[ 0.320877] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000a400
[ 0.320931] usb usb7: configuration #1 chosen from 1 choice
[ 0.320949] hub 7-0:1.0: USB hub found
[ 0.320953] hub 7-0:1.0: 2 ports detected
[ 0.320982] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.320986] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 0.320988] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 0.321007] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
[ 0.321025] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000a480
[ 0.321081] usb usb8: configuration #1 chosen from 1 choice
[ 0.321099] hub 8-0:1.0: USB hub found
[ 0.321104] hub 8-0:1.0: 2 ports detected
[ 0.321174] PNP: No PS/2 controller found. Probing ports directly.
[ 0.323964] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.323968] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.324049] mice: PS/2 mouse device common for all mice
[ 0.324134] rtc_cmos 00:03: RTC can wake from S4
[ 0.324164] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 0.324187] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 0.324257] device-mapper: uevent: version 1.0.3
[ 0.372491] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 0.408716] Freeing initrd memory: 13280k freed
[ 0.413796] device-mapper: multipath: version 1.1.0 loaded
[ 0.413800] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 0.413943] EISA: Probing bus 0 at eisa.0
[ 0.413949] Cannot allocate resource for EISA slot 1
[ 0.413963] Cannot allocate resource for EISA slot 8
[ 0.413965] EISA: Detected 0 cards.
[ 0.414015] cpuidle: using governor ladder
[ 0.414016] cpuidle: using governor menu
[ 0.414336] TCP cubic registered
[ 0.414439] NET: Registered protocol family 10
[ 0.414777] lo: Disabled Privacy Extensions
[ 0.415006] NET: Registered protocol family 17
[ 0.415464] Using IPI No-Shortcut mode
[ 0.415553] PM: Resume from disk failed.
[ 0.415566] registered taskstats version 1
[ 0.416024] Magic number: 14:344:996
[ 0.416108] rtc_cmos 00:03: setting system clock to 2010-10-01 17:58:29 UTC (1285955909)
[ 0.416111] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 0.416113] EDD information not available.
[ 0.610352] ata3: SATA link down (SStatus 0 SControl 300)
[ 0.610458] usb 1-1: new high speed USB device using ehci_hcd and address 2
[ 0.632733] isapnp: No Plug & Play device found
[ 0.740822] usb 1-1: configuration #1 chosen from 1 choice
[ 0.851754] usb 1-2: new high speed USB device using ehci_hcd and address 3
[ 0.938318] ata2.00: SATA link down (SStatus 0 SControl 300)
[ 0.938330] ata2.01: SATA link down (SStatus 0 SControl 300)
[ 1.084053] ata1.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.084063] ata1.01: SATA link down (SStatus 0 SControl 300)
[ 1.092283] ata1.00: ATA-7: SAMSUNG HD753LJ, 1AA01113, max UDMA7
[ 1.092286] ata1.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 1.100298] ata1.00: configured for UDMA/133
[ 1.100410] scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD753LJ 1AA0 PQ: 0 ANSI: 5
[ 1.100527] sd 0:0:0:0: [sda] 1465149168 512-byte logical blocks: (750 GB/698 GiB)
[ 1.100529] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.100574] sd 0:0:0:0: [sda] Write Protect is off
[ 1.100577] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.100599] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.100734] sda: sda1 sda2 <sda5>
[ 1.135039] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.208037] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.372006] usb 1-2: device not accepting address 3, error -71
[ 1.400195] ata4.00: ATAPI: TSSTcorp CDDVDW SH-S202N, SB02, max UDMA/66
[ 1.400210] ata4.00: applying bridge limits
[ 1.448218] ata4.00: configured for UDMA/66
[ 1.484010] usb 1-2: new high speed USB device using ehci_hcd and address 4
[ 1.539965] scsi 3:0:0:0: CD-ROM TSSTcorp CDDVDW SH-S202N SB02 PQ: 0 ANSI: 5
[ 1.617183] usb 1-2: configuration #1 chosen from 2 choices
[ 1.690094] sr0: scsi3-mmc drive: 12x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.690097] Uniform CD-ROM driver Revision: 3.20
[ 1.690177] sr 3:0:0:0: Attached scsi CD-ROM sr0
[ 1.690218] sr 3:0:0:0: Attached scsi generic sg1 type 5
[ 1.690259] Freeing unused kernel memory: 656k freed
[ 1.690678] Write protecting the kernel text: 4684k
[ 1.690718] Write protecting the kernel read-only data: 1840k
[ 1.709953] ramzswap: disk size set to 1677528 kB
[ 1.715148] udev: starting version 151
[ 1.741961] Adding 1677524k swap on /dev/ramzswap0. Priority:100 extents:1 across:1677524k SS
[ 1.810540] sky2 driver version 1.25
[ 1.810581] sky2 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 1.810595] sky2 0000:02:00.0: setting latency timer to 64
[ 1.810619] sky2 0000:02:00.0: Yukon-2 EC Ultra chip revision 3
[ 1.810702] alloc irq_desc for 28 on node -1
[ 1.810704] alloc kstat_irqs on node -1
[ 1.810716] sky2 0000:02:00.0: irq 28 for MSI/MSI-X
[ 1.811387] sky2 eth0: addr 00:22:15:46:1c:ab
[ 1.820977] vga16fb: initializing
[ 1.820980] vga16fb: mapped to 0xc00a0000
[ 1.821033] fb0: VGA16 VGA frame buffer device
[ 1.822634] ahci 0000:03:00.0: version 3.0
[ 1.823892] pata_marvell 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.823919] pata_marvell 0000:03:00.0: setting latency timer to 64
[ 1.830999] Linux agpgart interface v0.103
[ 1.832364] scsi4 : pata_marvell
[ 1.833064] Floppy drive(s): fd0 is 1.44M
[ 1.837938] scsi5 : pata_marvell
[ 1.838040] ata5: PATA max UDMA/100 cmd 0xdc00 ctl 0xd880 bmdma 0xd400 irq 16
[ 1.838043] ata6: PATA max UDMA/133 cmd 0xd800 ctl 0xd480 bmdma 0xd408 irq 16
[ 1.840781] skge 0000:05:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 1.840819] skge 1.13 addr 0xfebfc000 irq 18 chip Yukon-Lite rev 9
[ 1.841546] skge eth1: addr 00:22:15:46:34:4c
[ 1.846297] Initializing USB Mass Storage driver...
[ 1.846383] scsi6 : SCSI emulation for USB Mass Storage devices
[ 1.846512] usb-storage: device found at 2
[ 1.846514] usb-storage: waiting for device to settle before scanning
[ 1.846535] scsi7 : SCSI emulation for USB Mass Storage devices
[ 1.846646] usbcore: registered new interface driver usb-storage
[ 1.846649] USB Mass Storage support registered.
[ 1.846734] usb-storage: device found at 4
[ 1.846736] usb-storage: waiting for device to settle before scanning
[ 1.852136] FDC 0 is a post-1991 82077
[ 2.080011] usb 4-1: new full speed USB device using uhci_hcd and address 2
[ 2.170872] ohci1394 0000:05:03.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 2.224050] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[19] MMIO=[febfb000-febfb7ff] Max Packet=[2048] IR/IT contexts=[8/8]
[ 2.278237] usb 4-1: configuration #1 chosen from 1 choice
[ 2.320107] Console: switching to colour frame buffer device 80x30
[ 2.524011] usb 4-2: new low speed USB device using uhci_hcd and address 3
[ 2.695943] xor: automatically using best checksumming function: pIII_sse
[ 2.712005] pIII_sse : 7636.000 MB/sec
[ 2.712007] xor: using function: pIII_sse (7636.000 MB/sec)
[ 2.712109] usb 4-2: configuration #1 chosen from 1 choice
[ 2.714773] device-mapper: dm-raid45: initialized v0.2594b
[ 2.733246] usbcore: registered new interface driver hiddev
[ 2.765144] input: Touchkit Touch as /devices/pci0000:00/0000:00:1a.1/usb4/4-2/4-2:1.0/input/input3
[ 2.765260] generic-usb 0003:0EEF:0001.0001: input,hiddev96,hidraw0: USB HID v1.12 Pointer [Touchkit Touch] on usb-0000:00:1a.1-2/input0
[ 2.765278] usbcore: registered new interface driver usbhid
[ 2.765281] usbhid: v2.6:USB HID core driver
[ 2.911889] EXT4-fs (sda1): mounted filesystem with ordered data mode
[ 2.960044] usb 6-2: new low speed USB device using uhci_hcd and address 2
[ 3.144972] usb 6-2: configuration #1 chosen from 1 choice
[ 3.500127] ieee1394: Host added: ID:BUS[0-00:1023] GUID[001e8c00015dffb5]
[ 6.844102] usb-storage: device scan complete
[ 6.844220] usb-storage: device scan complete
[ 6.844481] scsi 6:0:0:0: Direct-Access Generic External 2.02 PQ: 0 ANSI: 4
[ 6.844642] scsi 7:0:0:0: Direct-Access Apple iPod 2.70 PQ: 0 ANSI: 2
[ 6.844874] sd 6:0:0:0: Attached scsi generic sg2 type 0
[ 6.845227] sd 7:0:0:0: Attached scsi generic sg3 type 0
[ 6.845587] sd 6:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[ 6.845835] sd 7:0:0:0: [sdc] 495616 2048-byte logical blocks: (1.01 GB/968 MiB)
[ 6.846331] sd 6:0:0:0: [sdb] Write Protect is off
[ 6.846333] sd 6:0:0:0: [sdb] Mode Sense: 21 00 00 00
[ 6.846336] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 6.846456] sd 7:0:0:0: [sdc] Write Protect is off
[ 6.846459] sd 7:0:0:0: [sdc] Mode Sense: 64 00 00 08
[ 6.846461] sd 7:0:0:0: [sdc] Assuming drive cache: write through
[ 6.847583] sd 7:0:0:0: [sdc] 495616 2048-byte logical blocks: (1.01 GB/968 MiB)
[ 6.847759] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 6.847762] sdb:
[ 6.848081] sd 7:0:0:0: [sdc] Assuming drive cache: write through
[ 6.848083] sdc: sdb1 sdb2 <sdb5>
[ 6.850393] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 6.850396] sd 6:0:0:0: [sdb] Attached SCSI disk
[ 6.858834]
[ 6.859706] sd 7:0:0:0: [sdc] 495616 2048-byte logical blocks: (1.01 GB/968 MiB)
[ 6.860207] sd 7:0:0:0: [sdc] Assuming drive cache: write through
[ 6.860210] sd 7:0:0:0: [sdc] Attached SCSI removable disk
[ 12.427520] udev: starting version 151
[ 12.519974] Adding 9827320k swap on /dev/sda5. Priority:-1 extents:1 across:9827320k
[ 12.527344] lp: driver loaded but no devices found
[ 12.695799] nvidia: module license 'NVIDIA' taints kernel.
[ 12.695802] Disabling lock debugging due to kernel taint
[ 12.742792] type=1505 audit(1285955921.824:2): operation="profile_load" pid=722 name="/sbin/dhclient3"
[ 12.743469] type=1505 audit(1285955921.824:3): operation="profile_load" pid=722 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 12.743838] type=1505 audit(1285955921.824:4): operation="profile_load" pid=722 name="/usr/lib/connman/scripts/dhclient-script"
[ 13.536829] usbcore: registered new interface driver usbserial
[ 13.537274] USB Serial support registered for generic
[ 13.537688] input: Microsft Microsoft Wireless Desktop Receiver 3.1 as /devices/pci0000:00/0000:00:1d.0/usb6/6-2/6-2:1.0/input/input4
[ 13.537767] microsoft 0003:045E:00F9.0002: input,hidraw1: USB HID v1.11 Keyboard [Microsft Microsoft Wireless Desktop Receiver 3.1] on usb-0000:00:1d.0-2/input0
[ 13.628289] microsoft 0003:045E:00F9.0003: fixing up Microsoft Wireless Receiver Model 1028 report descriptor
[ 13.677431] input: Microsft Microsoft Wireless Desktop Receiver 3.1 as /devices/pci0000:00/0000:00:1d.0/usb6/6-2/6-2:1.1/input/input5
[ 13.677528] microsoft 0003:045E:00F9.0003: input,hidraw2: USB HID v1.11 Mouse [Microsft Microsoft Wireless Desktop Receiver 3.1] on usb-0000:00:1d.0-2/input1
[ 13.677823] usbcore: registered new interface driver usbserial_generic
[ 13.677826] usbserial: USB Serial Driver core
[ 13.685472] USB Serial support registered for FTDI USB Serial Device
[ 13.685543] ftdi_sio 4-1:1.0: FTDI USB Serial Device converter detected
[ 13.685564] usb 4-1: Detected FT232RL
[ 13.685566] usb 4-1: Number of endpoints 2
[ 13.685568] usb 4-1: Endpoint 1 MaxPacketSize 64
[ 13.685570] usb 4-1: Endpoint 2 MaxPacketSize 64
[ 13.685572] usb 4-1: Setting MaxPacketSize 64
[ 13.687715] usb 4-1: FTDI USB Serial Device converter now attached to ttyUSB0
[ 13.687746] usbcore: registered new interface driver ftdi_sio
[ 13.687748] ftdi_sio: v1.5.0:USB FTDI Serial Converters Driver
[ 13.695163] alloc irq_desc for 22 on node -1
[ 13.695166] alloc kstat_irqs on node -1
[ 13.695173] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 13.695204] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 13.762856] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 13.762863] nvidia 0000:01:00.0: setting latency timer to 64
[ 13.762868] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[ 13.763010] NVRM: loading NVIDIA UNIX x86 Kernel Module 195.36.24 Thu Apr 22 09:18:20 PDT 2010
[ 13.905653] sky2 eth0: enabling interface
[ 13.906104] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 13.908766] skge eth1: enabling interface
[ 13.913825] type=1505 audit(1285955922.995:5): operation="profile_load" pid=978 name="/usr/share/gdm/guest-session/Xsession"
[ 13.914591] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 13.916841] type=1505 audit(1285955922.999:6): operation="profile_replace" pid=979 name="/sbin/dhclient3"
[ 13.917524] type=1505 audit(1285955922.999:7): operation="profile_replace" pid=979 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 13.917892] type=1505 audit(1285955922.999:8): operation="profile_replace" pid=979 name="/usr/lib/connman/scripts/dhclient-script"
[ 13.924186] type=1505 audit(1285955923.007:9): operation="profile_load" pid=982 name="/usr/bin/evince"
[ 13.934119] type=1505 audit(1285955923.015:10): operation="profile_load" pid=982 name="/usr/bin/evince-previewer"
[ 13.939587] type=1505 audit(1285955923.019:11): operation="profile_load" pid=982 name="/usr/bin/evince-thumbnailer"
[ 13.980689] Mantis 0000:05:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 13.980731] irq: 16, latency: 64
[ 13.980732] memory: 0xf8fff000, mmio: 0xf8c8e000
[ 13.980735] found a VP-2040 PCI DVB-C device on (05:00.0),
[ 13.980738] Mantis Rev 1 [113b:1178], irq: 16, latency: 64
[ 13.980740] memory: 0xf8fff000, mmio: 0xf8c8e000
[ 14.006098] MAC Address=[00:08:ca:18:81:c0]
[ 14.006147] mantis_alloc_buffers (0): DMA=0x33e40000 cpu=0xf3e40000 size=262144
[ 14.006152] mantis_alloc_buffers (0): RISC=0x341a7000 cpu=0xf41a7000 size=1000
[ 14.006155] DVB: registering new adapter (Mantis dvb adapter)
[ 14.116421] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input6
[ 14.524110] mantis_frontend_init (0): Probing for CU1216 (DVB-C)
[ 14.572357] TDA10021: i2c-addr = 0x0c, id = 0x79
[ 14.572359] mantis_frontend_init (0): found Philips CU1216 DVB-C frontend (TDA10021) @ 0x0c
[ 14.572361] mantis_frontend_init (0): Mantis DVB-C Philips CU1216 frontend attach success
[ 14.572365] DVB: registering adapter 0 frontend 0 (Philips TDA10021 DVB-C)...
[ 14.572438] mantis_ca_init (0): Registering EN50221 device
[ 14.652020] mantis_ca_init (0): Registered EN50221 device
[ 14.652029] mantis_hif_init (0): Adapter(0) Initializing Mantis Host Interface
[ 14.652088] input: Mantis VP-2040 IR Receiver as /devices/virtual/input/input7
[ 14.652138] Creating IR device irrcv0
[ 14.752008] Mantis VP-2040 IR Receiver: unknown key for scancode 0x0000
[ 14.752011] Mantis VP-2040 IR Receiver: unknown key: key=0x00 down=1
[ 14.852012] Mantis VP-2040 IR Receiver: unknown key: key=0x00 down=0
[ 15.180005] hda-intel: azx_get_response timeout, switching to polling mode: last cmd=0x02ab0001
[ 15.897706] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control rx
[ 16.304494] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 17.288197] ppdev: user-space parallel port driver
[ 17.597048] CPU0 attaching NULL sched-domain.
[ 17.597053] CPU1 attaching NULL sched-domain.
[ 17.624754] CPU0 attaching sched-domain:
[ 17.624757] domain 0: span 0-1 level MC
[ 17.624760] groups: 0 1
[ 17.624765] CPU1 attaching sched-domain:
[ 17.624767] domain 0: span 0-1 level MC
[ 17.624770] groups: 1 0
[ 18.831551] CPU0 attaching NULL sched-domain.
[ 18.831557] CPU1 attaching NULL sched-domain.
[ 18.852562] CPU0 attaching sched-domain:
[ 18.852565] domain 0: span 0-1 level MC
[ 18.852568] groups: 0 1
[ 18.852573] CPU1 attaching sched-domain:
[ 18.852575] domain 0: span 0-1 level MC
[ 18.852578] groups: 1 0
[ 20.770978] EXT4-fs (sdb1): mounted filesystem with ordered data mode
[ 26.600005] eth0: no IPv6 routers present
[ 37.408866] __ratelimit: 9 callbacks suppressed
[ 37.408869] type=1503 audit(1285955946.492:15): operation="open" pid=1783 parent=1772 profile="/usr/sbin/cupsd" requested_mask="w::" denied_mask="w::" fsuid=0 ouid=0 name="/dev/ttyUSB0"
[ 154.868012] dvb_ca adapter 0: DVB CAM did not respond :(
[ 273.646286] type=1503 audit(1285956182.728:16): operation="open" pid=1965 parent=1954 profile="/usr/sbin/cupsd" requested_mask="w::" denied_mask="w::" fsuid=0 ouid=0 name="/dev/ttyUSB0"
[ 791.898574] lo: Disabled Privacy Extensions
welmar@welmar-desktop:~$

nm
Johtava konsultti
Viestit: 3160
Liittynyt: 22.07.2005 3:00

Viesti Kirjoittaja nm » 02.10.2010 2:36

welmar kirjoitti:Tällä hetkellä tilanne olis sellainen että kaffeine löytää kortin ja tunnistaa sen Philips TDA10021 DVB-C:nä. Myös Järjestelmä>Ylläpito>Laiteajurit näyttää Mantis ajurit ja ilmoittaa niiden olevan käytössä. Kaiken pitäisi siis olla hyvin mutta kun yritän scannata saan ilmoituksen Vastaanottolaitetta ei löydy.
Eli saatko tämän virheen Kaffeine 1.0pre3:lla? Oletko kokeillut muita ohjelmia, kuten VLC:tä tai MPlayeriä, valmiin channels.confin avulla? Kaffeinen 1.0-esiversiot ovat niin bugisia, että virhe voi hyvinkin johtua ohjelmasta itsestään.

Mitä dvb-appsin scan-työkalu sanoo päätteessä, kun ajat sitä näin:

Koodi: Valitse kaikki

scan /usr/share/dvb/dvb-c/fi-HTV
[ 13.980689] Mantis 0000:05:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 13.980731] irq: 16, latency: 64
[ 13.980732] memory: 0xf8fff000, mmio: 0xf8c8e000
[ 13.980735] found a VP-2040 PCI DVB-C device on (05:00.0),
[ 13.980738] Mantis Rev 1 [113b:1178], irq: 16, latency: 64
[ 13.980740] memory: 0xf8fff000, mmio: 0xf8c8e000
[ 14.006098] MAC Address=[00:08:ca:18:81:c0]
[ 14.006147] mantis_alloc_buffers (0): DMA=0x33e40000 cpu=0xf3e40000 size=262144
[ 14.006152] mantis_alloc_buffers (0): RISC=0x341a7000 cpu=0xf41a7000 size=1000
[ 14.006155] DVB: registering new adapter (Mantis dvb adapter)
[ 14.116421] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input6
[ 14.524110] mantis_frontend_init (0): Probing for CU1216 (DVB-C)
[ 14.572357] TDA10021: i2c-addr = 0x0c, id = 0x79
[ 14.572359] mantis_frontend_init (0): found Philips CU1216 DVB-C frontend (TDA10021) @ 0x0c
[ 14.572361] mantis_frontend_init (0): Mantis DVB-C Philips CU1216 frontend attach success
[ 14.572365] DVB: registering adapter 0 frontend 0 (Philips TDA10021 DVB-C)...
[ 14.572438] mantis_ca_init (0): Registering EN50221 device
[ 14.652020] mantis_ca_init (0): Registered EN50221 device
[ 14.652029] mantis_hif_init (0): Adapter(0) Initializing Mantis Host Interface
Tuo näyttää kyllä ihan hyvältä, eli kortin pitäisi olla käyttökunnossa.

welmar
Harrastaja
Viestit: 53
Liittynyt: 06.09.2010 12:40
Paikkakunta: Helsinki

Viesti Kirjoittaja welmar » 03.10.2010 11:13

welmar@welmar-desktop:~$ scan /usr/share/dvb/dvb-c/fi-HTV
scanning /usr/share/dvb/dvb-c/fi-HTV
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
main:2273: FATAL: failed to open '/dev/dvb/adapter0/frontend0': 16 Device or resource busy
En tiedä mistä tämä virheilmoitus johtuu kun ei ole ainakaan mikään soitin päällä samaan aikaan. VLC antaa tälläisen:Syötettä ei voi avata:
VLC ei kyennyt avaamaan MRL-sijaintia "dvb://". Katso lokista lisätietoja. Mistä toi vlc:n loki löytyy? MeTv ilmoittaa ettei ole digitaalista sovitinta saatavilla.

nm
Johtava konsultti
Viestit: 3160
Liittynyt: 22.07.2005 3:00

Viesti Kirjoittaja nm » 03.10.2010 14:31

welmar kirjoitti: main:2273: FATAL: failed to open '/dev/dvb/adapter0/frontend0': 16 Device or resource busy
Tutki käyttääkö joku prosessi tuota laitetta:

Koodi: Valitse kaikki

sudo lsof /dev/dvb/adapter0/frontend0

welmar
Harrastaja
Viestit: 53
Liittynyt: 06.09.2010 12:40
Paikkakunta: Helsinki

Viesti Kirjoittaja welmar » 03.10.2010 16:52

vdr näytti olevan käynnissä vaikka en muista edes asentaneeni sitä. Poistin vdr:n kokonaan ja sen jälkeen scan näyttää:welmar@welmar-desktop:~$ scan /usr/share/dvb/dvb-c/fi-HTV
scanning /usr/share/dvb/dvb-c/fi-HTV
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
main:2273: FATAL: failed to open '/dev/dvb/adapter0/frontend0': 2 No such file or directory
Vdr:n poiston jälkeen kaffeine löytää kaksi laitetta Philips TDA10021 DVB-C ja TDA10023 DVB_C:n kun ennen se löysi vain toisen. Koneessa on vain yksi viritin mutta olisiko toi toinen kortinlukija vai onko tässä jokin virhe? Molempien laitteiden kohdalla lukee ettei niitä ole kytketty.

mal--
Isäntä
Viestit: 96
Liittynyt: 13.02.2010 10:54

Viesti Kirjoittaja mal-- » 03.10.2010 17:27

welmar kirjoitti:vdr näytti olevan käynnissä vaikka en muista edes asentaneeni sitä. Poistin vdr:n kokonaan ja sen jälkeen scan näyttää:welmar@welmar-desktop:~$ scan /usr/share/dvb/dvb-c/fi-HTV
scanning /usr/share/dvb/dvb-c/fi-HTV
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
main:2273: FATAL: failed to open '/dev/dvb/adapter0/frontend0': 2 No such file or directory
Vdr:n poiston jälkeen kaffeine löytää kaksi laitetta Philips TDA10021 DVB-C ja TDA10023 DVB_C:n kun ennen se löysi vain toisen. Koneessa on vain yksi viritin mutta olisiko toi toinen kortinlukija vai onko tässä jokin virhe? Molempien laitteiden kohdalla lukee ettei niitä ole kytketty.
Tuleeko sinulla /var/log/syslog:iin jotain tyyliin "DVB: registering adapter 0 frontend 0" edellisen bootin kohdalla? Löytyykö kansiosta /dev/dvb/ adaptereita ja niiden alta mitään?

Vastaa Viestiin